Milodon Small Block Chevy Street and Strip Oil Pans

STREET & STRIP  OIL PANS

Made InTHe USA
  • Designed for Heavy Street Use and Drag Strip Applications.
  • Clears Stock Chassis and Steering, As Listed, and Most Headers.
  • These Highly Engineered Oil Pans Actually Free Up Additional Horsepower.
  • Deep Sumps Provide Ample Oil Supply When Ground Clearance is Adequate.
  • Low Profiles Allow Adequate Oil Supply & Maximum Available Ground Clearance.
  • A Necessity For High Volume Oil Pumps and Increased RPM Ranges.

- Small Block Chevy -
LOW PROFILE DESIGN
Small Block Chevy Street Strip Milodon Oil Pan#30900
The Low Profile "triangulated" sump design that was originally developed by Milodon over three decades ago gives both adequate ground clearance, as well as sufficient oil capacity for any kind of high performance use.  This pan is equally suited for use on the street or strip.  It will fit all Chevy chassis, except '62-'67 Nova. Oil control baffles 100% subdue oil movement and provide increased horsepower. High strength magnetic drain plug included.

* Pan fits a 3.750" 400 stroke crank with steel stock rods.  Eagle's 400 rods may need slight fitting.

* Pan Capacity is 7 Quarts Plus Filter - 8 1/4" Sump Depth
Left Hand Dipstick (1955-79), drivers side dipstick 30900
Right Hand Dipstick 1980-85 & Dart SHP block, passenger side stick, 2 pc rear main 30901
Right Hand Dipstick (1986-Present), passenger side dipstick, 1 pc rear main 30902
Left Hand Dipstick in Australian Holden LC / LJ
30905 Pan Capacity is 6 Quarts Plus Filter - 7" Sump Length		 30905

Oil Pump and Pick-Up Required
Pickup for 18750 pump orMelling M55HV / 10550 18314 
Pickup for 18740 3/4inch inlet pump or Melling M155HV 18214 
Extreme Duty Pickup for 18750 or Melling M55HV / 10550 18316 
Pickup for stock Chevy or Milodon 18755 18311 
Pickup for 18770, Big Block style pump 18301 
Oil Pump - High Volume 18750 
Oil Pump - Standard Volume 18755 
Oil Pump Shaft 23050 
Oil Pan Gasket 40100 
Oil Pan Gasket - 1 Piece 41000 
Windage Tray - 350 Left side stick, Street / Strip, Louvered 32100 
Windage Tray - 400 Left side stick, Street / Strip, Louvered 32101 
Windage Tray - Right side stick, Street / Strip, Louvered 32102 
Windage Tray - Race, Screen 32250 
Windage Tray Install Kit 81150 
Rear Pan Baffle 32500 
Oil Pan Bolts, vibration resistant 85000 
Oil Pan Studs, vibration resistant nuts 81300 
Oil Pan Dipstick - Up to 1979, drivers side 22000 
Oil Pan Dipstick - 1980 & Up, passenger side 22005 
STROKER LOW PROFILE - Allows 4" Stroke Crank
Small Block Chevy Stroker Milodon Oil Pan#30908
High power output design uses a  deeper pan front to allow the use of a full length competition style windage to yield the most available power. Tray fastened into the pan so no extra mounting is required. Pan fits stock crossmember without modification when the correct Tall-Narrow frame and engine motor mounts are used. The Short-Wide mounts can not be used. Low profile sump allows good ground clearance, use of the stock starter and oil filter yet increases capacity. Includes high strength magnetic drain plug.
Pan fits a 4" stroke crank with steel Carillo or Eagle style rods.
Pan Capacity is 6 Quarts Plus Filter - 8  1/4" Sump Depth
Left Hand Dipstick (1955-79) 30908 
Left Hand Dipstick (1955-79) - no tray installed & silver plated 30906 
Right Hand Dipstick - Dart SHP block & 1980-85 GM blocks 30907 
Right Hand Dipstick (1986 & Up) 30909 
NOTE: For engines over 430 cubic inches or engines that see nitrous or blown use, 
              the Extreme Duty pickup #18316 must be used.

Oil Pump and Pick-Up Required:
Extreme Duty pickup with 18750 pump 18316 
Pickup with 18750 pump 18314 
Pickup with 18740 3/4inch inlet pump or Melling M155HV 18214 
Pickup with 18750 pump 18314 
Pickup with 18755 pump 18311 
Oil Pump - High Volume 18750 
Oil Pump - Standard Volume 18755 
Oil Pump Shaft 23050 
Oil Pan Stroker Gasket 40105 
Oil Pan Stroker Gasket - 1 Piece 41010 
Rear Pan Baffle 32500 
Oil Pan Bolts, vibration resistant 85000 
Oil Pan Studs, vibration resistant nuts 81300 
Oil Pan Dipstick - Up to 1979, drivers side 22000 
Oil Pan Dipstick - 1986 & Up, passenger side 22005 
DEEP SUMP
Small Block Chevy Deep Sump Milodon Oil Pan #30401
The only oil pan of its kind in the industry. Milodon's exclusive all one-piece deep sump is manufactured with no external welds. Oil control baffles 100% contain oil movement, which provides consistent oil pressure and avoids horsepower loss. Fits all Chevy chassis, except 1962-67 Nova. High strength magnetic drain plug included.

Pan fits a 3.750" 400 stroke crank with steel stock rods.  Eagle's 400" rods may need slight fitting.

Pan Capacity is 6 Quarts Plus Filter - 8  1/2" Sump Depth
Left Hand Dipstick, drivers side (Up to 1979) 30401  

Oil Pump and Pick-Up Required:
Stock Chevy or Milodon 18755 18311 
Milodon 18750 or Melling M55HV, 10550 18314 
Pickup with 18750 3/4inch inlet pump 18214 
Oil Pump - High Volume 18750 
Oil Pump - Standard Volume 18755 
Oil Pump Shaft 23050 
Oil Pan Gasket 40100 
Oil Pan Gasket - 1 Piece 41000 
Windage Tray - Street / Strip, Louvered 32100 
Windage Tray - Race, Screen 32250 
Windage Tray Install Kit 81150 
Rear Pan Baffle 32500 
Oil Pan Bolts, vibration resistant 85000 
Oil Pan Studs, vibration resistant nuts 81300 
Oil Pan Dipstick - Up to 1979, drivers side 22000 
STREET PERFORMANCE
Small Block Chevy Street Milodon Oil Pan#31503
Specifically designed for applications that desire improvements over stock yet do not want a high cost racing pan. While appearing stock on the outside, it contains sufficient horizontal baffling to 100% control 5 quarts of oil. Internal mounted windage tray provides increased power yet requires no block mounting to install. Fits all Chevy chassis except 62-67 Nova. A complete low cost performance package. High strength magnetic drain plug included.

Pan fits a 3.750" 400 stroke crank with steel stock rods.  Eagle's 400 rods may need slight fitting

Pan Capacity is 5 Quarts Plus Filter - 7  1/2" Sump Depth
1979 & Earlier (L/H Dipstick) 31503 
1980-85 & Dart SHP block, passenger side stick, 2 pc rear main 31502 
1986 & Up (R/H Dipstick) 31501 

Oil Pump and Pick-Up Required:
Pickup 18307 
Oil Pump, standard volume 18755 
Oil Pump, high volume 18750 
Oil Pump Shaft 23050 
Oil Pan Gasket 40100 
Oil Pan Gasket, up to 1976 driver side stick, 1 piece 41000 
Oil Pan Gasket, 86 & up, passenger side stick, 1 piece 41001 
Rear Pan Baffle 32500 
Oil Pan Bolts, vibration resistant 85000 
Oil Pan Studs, vibration resistant nuts 81300 
Oil Pan Dipstick - Up to 1979, drivers side 22000 
Oil Pan Dipstick - 1986 & Up, passenger side 22005 

- LS / GEN III - ENGINE SWAP PANS -
See LS Chevy Page for Complete Listings

LS Chevy Oil Pan#30915
LOW PROFILE with Billet Filter Plate -
      Allows installation of LS and Gen III engines into early pre-1975 Camaro, Chevelle, 68 & up Novas and 55-57 Chevys. While this pan uses heavy duty steel and double thick pan rails, it is actually 5 1/2 pounds lighter than the factory aluminum oil pan. The increased oil capacity and increased oil control of the Milodon pan allows for consistent oil pressure under heavy usage and more available power.
      The factory filter location on the pan is replaced by a remote oil filter kit that allows convenient placement as desired. The oil pan includes the fitting plate and fittings where the oil exists the block. The additional required #21575 filter kit includes all other required brass fittings and 3 feet of 10 AN, 250 PSI line. These push-together oil lines can be cut to length and are easy to assemble and very secure. High strength magnetic drain plug included.
Pan Capacity is 7 Quarts Plus Filter - 6" Sump Depth
All chassis, except 62-67 Nova & 55-57 Chevy 30915 
1955-57 Chevy 30916 

Oil Pump and Pick-Up Required:
Pickup 18290
Oil Pump Stock                  
Oil Pan Gasket Stock                  
Oil Filter Kit 21575
Windage Tray 32150 
Dipstick, CNC stainless steel 22006 

 Note: Stainless steel dipstick requires use of headers to fit.
   - 62-67 CHEVY II NOVA DEEP SUMP -
Small Block Chevy Nova Milodon Oil Pan #31060
This rear sump pan is a requirement for any racing or high performance use, replacing the poorly designed stock front sump configuration. Will not work with stock power steering. High strength magnetic drain plug included.

Pan fits a 3.750" 400 stroke crank with steel stock rods.  Eagle's 400" rods may need slight fitting.

Pan Capacity is 6 Quarts Plus Filter - 9  1/2" Sump Depth
Left Hand Dipstick (1955-79) 31060 
Right Hand Dipstick 1980-85 & Dart SHP block, passenger side stick, 2 pc rear main 31061 
Right Hand Dipstick (1986 & Up) 31062 
LS Chevy - All LS series engines 31063 

Oil Pump and Pick-Up Required:
Milodon 18755, (M55) 18310 
Milodon 18750, (M55HV) 18313 
Oil Pump Shaft 23050 
Oil Pan Gasket 40100 
Oil Pan Gasket, Drivers side stick, 1 piece 41000 
Oil Pan Gasket, Passenger side stick, 1 piece 41001 
Windage Tray - 350 Left side stick, Street / Strip, Louvered 32100 
Windage Tray - 400 Left side stick, Street / Strip, Louvered 32101 
Windage Tray - Right side stick, Street / Strip, Louvered 32102 
Windage Tray - Race, Screen 32250 
Windage Tray Install Kit 81150 
Rear Pan Baffle 32500 
Oil Pan Bolts, vibration resistant 85000 
Oil Pan Studs, vibration resistant nuts 81300 
Oil Pan Dipstick - Up to 1979, drivers side 22000 
Oil Pan Dipstick - 1986 & Up, passenger side 22005 
VEGA AND MONZA
Small Block Chevy Vega Milodon Oil Pan #31070
Specially engineered for Small Block Chevrolet installations in Vega and Monza chassis. Designed to provide ample draglink clearance. Includes control baffles to 100% subdue unwanted oil movement and increase power output. Milodon Windage Trays #32100 and #32250 must be trimmed in front of No. 3 main cap mounting to clear shallow area of pan. High strength magnetic drain plug included.

Pan fits a 3.750" 400 stroke crank with stock  rods.

Pan Capacity is 6 Quarts Plus Filter - 7  3/4" Sump Depth

Left Hand Dipstick (1955-79) 31070 

Oil Pump and Pick-Up Required:
Stock Chevy or Milodon 18755 18312 
Milodon 18750 or Melling M55HV, 10550 18312 
Oil Pump - High Volume 18750 
Oil Pump - Standard Volume 18755 
Oil Pump Shaft 23050 
Oil Pan Gasket 40100 
Oil Pan Gasket - 1 Piece 41000 
Windage Tray - Street / Strip, Louvered 32100 
Windage Tray - Race, Screen 32250 
Windage Tray Install Kit 81150 
Rear Pan Baffle 32500 
Oil Pan Bolts, vibration resistant 85000 
Oil Pan Studs, vibration resistant nuts 81300 
Oil Pan Dipstick - Up to 1979, drivers side 22000 
   - S-10 BLAZER & PICKUP ENGINE SWAP -
Small Block Chevy S-10 Milodon Oil Pan #31080
Designed to allow the installation of a Small Block Chevy into an S-10 vehicle. The rear sump has increased oil capacity and increased oil control yielding more power and more consistent oil pressure. High strength magnetic drain plug included.
Pan fits a 4" stroke crank with steel Carillo or Eagle style rods.
Pan Capacity is 6 Quarts Plus Filter - 9  1/2" Sump Depth
Left Hand Dipstick (1955 - 1979) 31080 
Right Hand Dipstick 1980-85 & Dart SHP block, passenger side stick, 2 pc rear main 31081 
Right Hand Dipstick (1986 & Up) 31082 
LS Chevy - All LS series engines 31083 

Oil Pump and Pick-Up Required:
Milodon 18755, (M55) 18310 
Milodon 18750, (M55HV) 18313 
Oil Pump Shaft 23050 
Oil Pan Gasket 40100 
Oil Pan Gasket, 1 piece 41000 
Oil Pan Gasket, Passenger side stick, 1 piece 41001 
Windage Tray - 350 Left side stick, Street / Strip, Louvered 32100 
Windage Tray - 400 Left side stick, Street / Strip, Louvered 32101 
Windage Tray - Right side stick, Street / Strip, Louvered 32102 
Windage Tray - Race, Screen 32250 
Windage Tray Install Kit 81150 
Rear Pan Baffle 32500 
Oil Pan Bolts, vibration resistant 85000 
Oil Pan Studs, vibration resistant nuts 81300 
Oil Pan Dipstick - Up to 1979, drivers side 22000 
Oil Pan Dipstick - 1986 & Up, passenger side 22005 
Pick-Up to Pan Bottom Clearance MUST Be Checked and Adjusted to 1/4" to 3/8".
All Milodon Small Block Chevy Pans Require the 1977-79 Thick Front Seal, Contained in Milodon's "Crush-proof" Pan Gasket Set #40100.