|
#84327, #84287, #84351, #84427
|
ROCKER
ARM STUD KIT
Milodon's rocker arm stud kits are premium race
quality fasteners. Manufactured from tough 8740 steel, they feature
a large ground radius fillet to provide increased support to the
stud shank, effectively eliminating bending and subsequent breakage.
All Milodon studs are precision machined with rolled threads and
heat-treated for strength of 190,000 PSI. The complete stud has a
black oxide finish, and each kit contains 16 studs.
|
Small
Block Chevy, 3/8" -
Dim. "A" = 1.75 |
84327
|
Small
Block Chevy, 7/16" -
Dim. "A" = 1.75 |
84287
|
Big
Block Chevy -
Dim. "A" = 1.76 |
84427
|
Big
Block Chevy -
with double stud girdles, |
84351
|
| Small
Block Ford 302 |
84327
|
| Ford
Boss 302 |
84427
|
351 Cleveland -
Dim. "A" = 1.91 |
84351
|
| Pontiac
3/8" |
84327
|
| Pontiac
7/16" |
84287
|
|
|
#84500
|
INTAKE
MANIFOLD BOLTS
Compact 3/8" hex head bolt allows use of standard non 12 point socket wrench yet is easy to work with in tight quarters. These heat-treated intake bolts come complete with washers. |
| Small
Block Chevy - 6 pt. bolts |
85400
|
| Small
Block Chrysler - 6 pt. bolts |
85400
|
| Big Block Chrysler - 6 pt. bolts |
85400
|
| Big
Block Chevy - 6 pt. bolts |
85405
|
|
|
#85000
|
PAN
BOLTS
Designed especially for firmly holding oil pans in
place and not loosening up. Features a built-in washer face with
case-hardened serrations. The washer face and small head permits the
use of a socket wrench for quick and accurate installation.
Construction is such that they can be re-used time and time again. |
| Small
Block Chevy |
85000
|
LS / Gen III Chevy
- with Milodon pan only |
85002
|
| Big
Block Chevy |
85005
|
| Australian
Holden |
85008
|
Ford 302-460
(excluding 390-428) |
85010
|
|
Ford 390-428 |
85020
|
Ford 4.6 / 5.4
Liter
-
with Milodon pan only |
85015
|
| Chrysler 318-340-360 |
85020
|
| Chrysler 383-440 |
85020
|
| Olds 350-455 |
85000
|
| Pontiac350-455 |
85020
|
Chrysler 5.7 / 6.1 Hemi
- with Milodon pan only |
85025
|
|
|
#85375
|
VALUE
COVER STUDS
Permits rapid valve cover installation and removal. Guides valve cover and gasket into position. These studs are heat- treated and feature rolled threads and black oxided finish. Includes special serrated washer-faced nut. |
Small Block Chevy
1/4"
x 1 1/4" (set of 8) |
85375
|
Big Block Chevy & Ford 429 / 460
1/4"
x 1 1/4" ( set of 14) |
85376
|
Pontiac & Ford 428
5/16 x
11/2" (set of 10) |
85377
|
Chrys 318-360 & 383-440
Ford 302 & 253-308 Holden
1/4 x 11/4" (set of 12) |
85378
|
Olds & Ford 351-C
1/4 x 11/4" (set of 20) |
85379
|
| Replacement
Studs for Hold-Downs (set of 10) |
85380
|
|
|
|
#84550
|
ALUMINUM
BLOWER STUDS
Milodon aluminum blower studs and aluminum nuts are designed to
permit blower and manifold separation during unexpected blower
explosions without causing damage to the manifold and blower
housing, which would otherwise occur. Our studs are used by
professional racers in top Fuel, Funny Car and Alcohol classes and
are recommended for all supercharged applications. Fits 4.71, 6.71,
8.71, 10.71, 12.71, 14.71 GM superchargers. |
|
Studs, Nuts, and Washers
|
84550
|
|
|
#85260
|
FRONT TIMING COVER BOLTS
Specially designed to firmly hold timing cover in place, features a built-in washer face with case-hardened serrations. The washer face and small head permits the use of a socket wrench for quick and accurate installation. Construction is such that they can be re-used time and time again. Fits small and big block Chevy. |
Small & Big Block Chevy
1/4" x 1/2" 10
pack) |
85260
|
|
|
|
#84530
|
BALANCER
BOLTS
A necessary components for any serious engine
buildup. A balancer that isn't properly attached is not only
dangerous but will not do it's job of protecting the crank bearings
properly. Grade 8, heat-treated and thread rolled steel in a gold
irridited finish. Bolt features a 3/4" head for easy torquing
and engine turning by hand. Set includes bolt, lock washer and
1/4" thick flat washer. |
| Small
Block Chevy (7/16" - 20 x 2") |
84530
|
| Big
Block Chevy
(1/2" - 20 x 1-3/8") |
84532
|
|
|
#84500 #84510
|
BILLET BALANCER BOLTS
These premium quality 190,000 PSI crank bolts are
made in one piece from billet 8740 steel, using rolled threads after
heat-treat to aircraft quality specs. The washers are 4130 steel
which is heat-treated and parallel ground for flatness, producing
even load distribution.
|
| Small
Block Chevy (7/16" - 20) |
84500
|
| Big
Block Chevy (1/2" - 20) |
84510
|
| Chrysler
and Olds V8 (3/4" - 16) except most Small Block Chevy |
84520
|
| Ford (5/8" - 18) |
84525
|
|
|
#84540
|
HEADER
BOLTS
Grade 8, heat-treated header bolts. Compact 3/8" hex head bolt allows use of standard non 12 point socket wrench yet is easy to work with between header tubes. |
Small
Block Chevy, Big Block Chrysler, Pontiac -
3/8" x 3/4"
(set of 12) |
84540
|
Big
Block Chevy, Ford 302-351W, 390-428, 429-460 -
3/8" x 3/4"
(set of 16) |
84541
|
| Small
Block Chevy, Big Block Chrys, Pontiac for thick flanges - 3/8" x 1" (set of 12) |
84542
|
Big
Block Chevy, Ford 302-351W, 390-428, 429-460 for thick flanges-
3/8" x
1" (set of 16) |
84543
|
|
|
#81300
|
PAN STUDS
Undoubtedly the most professional method of attaching an oil pan is through the use of Milodon's pan stud kit, which includes heat-treated studs with rolled threads and special nuts with built-in serrated washer face. The kit provides easy pan installation, prolongs gasket life and the special serrated nuts guard against pan loosening during operation. |
| Small
Block Chevy and Olds |
81300
|
| Big
Block Chevy |
81305
|
| Australian
Holden V8 |
81308
|
Ford 302-460
(excluding 390-428) |
81310
|
|
Ford 390-428 |
81320
|
| Chrysler 318-340-360 |
81320
|
Chrysler
338-440 Wedge,
426 Hemi |
81320
|
| Chrysler
383-440 Wedge, 426 Hemi with 1/4" alum pans |
81325
|
| Olds 350-455 |
81300
|
| Pontiac350-455 |
81320
|
Universal
studs and nuts -
1/4" (10 pieces) |
81400
|
Universal
studs and nuts -
5/16" (10 pieces) |
81405
|
|
|
#81450
|
CARB
STUDS
These high quality carb studs feature premium quality rolled threads, Milodon innovated "starter nose" to ease thread starting and vibration-proof locking washer faced nuts. Studs
are black oxided and nuts are silver. |
1/2" thick flange carbs -
5/16" x 1 1/2" (set of 4) |
81450
|
1/2" carb flange & 1" thick spacer -
5/16" x 2 1/2"
(set of 4) |
81455
|
|
|
#81500
|
HEADER
STUDS
These thread rolled, thread starter nosed studs make installing headers a snap. The studs align the gasket and header flange allowing the header to slip on without the usual hassle, crossed threads and wasted time. Includes small 3/8" hex nuts for easy access. |
| Small Block Chevy |
81500
|
| Big Block Chevy |
81505
|
| GM Bellhousing Stud Kit |
81520
|
|
 |
BULK PACK
Designed especially for any application that needs
secure fastening without loosening up. Features a built-in washer
face with case-hardened serrations same as Milodon's pan bolts. The
washer face and small head permits the use of a socket wrench for
quick and accurate installation. |
| 10
Pack - 1/4" - 20 x 1/2" |
85250
|
| 10
Pack - 5/16" - 18 x 1/2" |
85270
|
|
|
